What kind of epoxy is used for tumblers?

Heat resistance: Choose heat resistant epoxy for tumblers. Normally, tumblers use epoxy resins that are cured with heat. Odor: Typically, it becomes difficult to work with resins that have a strong odor. Choose epoxy resins that are easier to work with.

What is the best resin to use for tumblers?

Metal Tumblers When using a metal tumbler, Stainless Steel is the best bet for applying resin to your tumbler. The Epoxy Resin adheres better to the Stainless Steel than any other metal and it does not need a coat of paint.

What is needed to make epoxy tumblers?

Along with at least three days, here’s a list of what you’ll need for your first tumbler:

  1. Stainless Steel Tumbler (I used a 20oz)
  2. Spray Paint.
  3. Painters Tape.
  4. Mod Podge.
  5. Silicone Brushes.
  6. Fine Glitter.
  7. Clear Coat Spray.
  8. Epoxy (Both A and B parts)

Do you have to use epoxy on tumblers?

If you ‘ re making tumblers, you need to be sure that the epoxy resin you ‘ re using is food safe after it’s cured and becomes an inert plastic. There’s a lot of different epoxies out there and not all are food safe.

You might be interested:  Question: How To Epoxy A Scarf Joint?

Is it safe to drink from epoxy tumblers?

ArtResin has been deemed safe for food contact once it has cured, but please keep food or beverages well away from ArtResin in its pre-cured liquid form. ArtResin is NOT edible or potable in either liquid or cured form. The maximum temperature cured ArtResin can come in contact with is 120F or 50C.

Can you make glitter tumblers without epoxy?

Make sure to remove the tape before the Mod Podge dries! There you have it! A way to make a decorated Yeti cup or Ozark tumbler without having to use epoxy. As you can see from the pictures, it’s not as smooth as epoxy but it still works and actually has a nice texture to it!

How many coats of epoxy do you put on a tumbler?

Whatever the project you ‘re working on, you ‘ll need several coats of epoxy resin and hardener. Most projects need between two and four. However many coats you ‘re planning on, you need to recoat at the right time and in the right way and ensure your surface is properly prepared.

How do I customize my tumblers with epoxy?

Instructions

  1. Wash tumbler.
  2. Apply tape to top (and bottom – optional).
  3. Spray paint the tumbler if needed. Let dry.
  4. Apply a layer of mod podge with long even strokes.
  5. Dump glitter all over while you are turning the tumbler so the mod podge is all covered.
  6. Remove tape.
  7. Let dry fully (over night).
  8. Time to epoxy.

Can you use a hair dryer on epoxy?

Can you use a hair dryer on epoxy? In short, YES a torch is the best tool to get rid of bubbles in epoxy resin. A hair dryer or heat gun doesn’t get hot enough to remove bubbles efficiently and can blow dust all over your wet resin.

You might be interested:  FAQ: How To Finish An Epoxy Table?

What can be used instead of epoxy?

Usually, hard plaster or concrete can be used as casting materials instead of epoxy resin.

What can you use other than epoxy on tumblers?

What Do you need to buy?

  • Brite Tone – If you want ONE item to use instead of epoxy, this would be it.
  • Glitter Glue – The Glitter glue is an awesome permanent adhesive that takes only 2 hours to dry.
  • Universal White – Universal White is the Crystalac primer and paint that can replace your need to spray paint.

How long does it take for epoxy to dry on a tumbler?

Usually, it takes around 72 hours to fully cure the epoxy. Whatever the dry time, the resin should be allowed to fully cure before attempting to move or sand it.

Leave a Reply

Your email address will not be published. Required fields are marked *