What can you use instead of epoxy for tumblers?

Are There Any Alternatives to Epoxy if You Want to Make Tumblers?

  • Crystalac (a water-based polyeurethane)
  • Clear Diamond Finish (a clear urethane)
  • 2K Clear Glamour Clear Coat (a spray urethane)

What epoxy do you use for cups?

STONE COAT Art Coat Resin For a professional touch to your creative project, Art Coat serves as one of the best crystal clear resins to epoxy tumblers. The 2-part kit with an easy to use 1:1 mixing ratio makes the topcoat easy to prepare that cures within 72 hours.

How do you cover a cup with epoxy?

Instructions

  1. Wash tumbler.
  2. Apply tape to top (and bottom – optional).
  3. Spray paint the tumbler if needed. Let dry.
  4. Apply a layer of mod podge with long even strokes.
  5. Dump glitter all over while you are turning the tumbler so the mod podge is all covered.
  6. Remove tape.
  7. Let dry fully (over night).
  8. Time to epoxy.

How long does it take to epoxy a cup?

Wait about 5-10 minutes and carefully (and with gloves still on) remove the tape from both the top and bottom. If you leave the tape on you’ll end up sealing it under the epoxy layer. Let the tumbler turner spin the cup slowly for 6-8 hours.

You might be interested:  Often asked: How To Remove Epoxy Resin From Table Top?

Can you use Mod Podge instead of epoxy?

It works as a sealant to your projects, you can gluwork your project with some classic mod podge and then use the Super Gloss over the top. So it gives you a very shiny, clear finish that looks like epoxy.

Can you make glitter tumblers without epoxy?

Make sure to remove the tape before the Mod Podge dries! There you have it! A way to make a decorated Yeti cup or Ozark tumbler without having to use epoxy. As you can see from the pictures, it’s not as smooth as epoxy but it still works and actually has a nice texture to it!

How many coats of epoxy do you put on a tumbler?

Whatever the project you ‘re working on, you ‘ll need several coats of epoxy resin and hardener. Most projects need between two and four. However many coats you ‘re planning on, you need to recoat at the right time and in the right way and ensure your surface is properly prepared.

What causes fish eyes in epoxy?

Substrate contamination is the most common problem that causes fish eyes and pin holes in epoxy seal coats. Dust, dirt, wax, silicones, even the oil from your fingers when touching the part prior to sealing with epoxy will deter epoxy resins from laying flat and curing with a perfectly smooth surface.

What can I use in place of epoxy?

Hard plaster or concrete can be good casting materials, and they’re cheaper than Milliput, Fimo or any resins. Definitely a good low cost material choice for larger pieces.

You might be interested:  What Will Take Epoxy Off?

Can you drink out of an epoxy Cup?

Can you really drink out of the cups? Absolutely! The cups are coated inside and out with a clear resin lining. The coating covers your entire cup and protects the wood from whatever you ‘re drinking.

What epoxy is food safe?

The MAX CLR A/B Epoxy Resin is an FDA Compliant coating system suitable for direct food contact. It is in accordance with CFR Title 21, Part 175.300, and 175.105 for direct and indirect food contact as a resinous adhesive or coatings. MAX CLR A/B is mixed 2:1 and provides 45 minutes of working time.

Is resin the same as epoxy?

Technically, there is no difference because epoxy is a resin. However, there are three different resins commonly deployed in DIY projects: epoxy resin, casting resin, and polyester resin, each with unique properties. Also important to note, epoxy resin and epoxy glue are different products.

Leave a Reply

Your email address will not be published. Required fields are marked *