What is needed to make epoxy tumblers?

Along with at least three days, here’s a list of what you’ll need for your first tumbler:

  1. Stainless Steel Tumbler (I used a 20oz)
  2. Spray Paint.
  3. Painters Tape.
  4. Mod Podge.
  5. Silicone Brushes.
  6. Fine Glitter.
  7. Clear Coat Spray.
  8. Epoxy (Both A and B parts)

What kind of epoxy is used for tumblers?

Heat resistance: Choose heat resistant epoxy for tumblers. Normally, tumblers use epoxy resins that are cured with heat. Odor: Typically, it becomes difficult to work with resins that have a strong odor. Choose epoxy resins that are easier to work with.

How much epoxy Do I need to mix for a tumbler?

First, you will want to ensure that you allow any spray paint to cure for 36 hours before applying your resin. Second, you will want to add an mL of resin for every ounce of the tumbler (for example, mix 20 ml for a 20 oz tumbler and 30 ml for a 30 oz tumbler and so on) to ensure you have enough resin for your tumbler.

You might be interested:  Often asked: How To Seal Epoxy?

Can you use a hair dryer on epoxy?

Can you use a hair dryer on epoxy? In short, YES a torch is the best tool to get rid of bubbles in epoxy resin. A hair dryer or heat gun doesn’t get hot enough to remove bubbles efficiently and can blow dust all over your wet resin.

Can you make glitter tumblers without epoxy?

Make sure to remove the tape before the Mod Podge dries! There you have it! A way to make a decorated Yeti cup or Ozark tumbler without having to use epoxy. As you can see from the pictures, it’s not as smooth as epoxy but it still works and actually has a nice texture to it!

Is it safe to epoxy acrylic tumblers?

And to get that pretty glass-like coating on our tumblers, we have to measure out an equal portion of both A side and B side and mix them together carefully ourselves. But once fully cured, epoxy is considered safe and is classified as a non-hazardous material.

Is it safe to drink from epoxy tumblers?

ArtResin has been deemed safe for food contact once it has cured, but please keep food or beverages well away from ArtResin in its pre-cured liquid form. ArtResin is NOT edible or potable in either liquid or cured form. The maximum temperature cured ArtResin can come in contact with is 120F or 50C.

What can be used instead of epoxy?

Usually, hard plaster or concrete can be used as casting materials instead of epoxy resin.

How long do you turn epoxy tumbler?

Once the entire surface has been evenly covered, allow it to turn until it is dry to the touch, within 18-24 hours. Once dry, remove the tape and allow it to finish curing. At 72 hours, it will have fully cured.

You might be interested:  Often asked: How To Remove Epoxy Floor Coating For Concrete Floors?

Can you use Mod Podge instead of epoxy?

It works as a sealant to your projects, you can gluwork your project with some classic mod podge and then use the Super Gloss over the top. So it gives you a very shiny, clear finish that looks like epoxy.

Do you have to sand between coats of epoxy on tumbler?

Do you have to sand epoxy tumblers? Sand the entire piece evenly. It will look terrible when you finish sanding it, but don’t worry. After you pour the second coat of epoxy, it will look good as new!

Why does my epoxy tumbler have dimples?

Dimples can occur for 3 reasons: temperature fluctuation, micro dust particles and overtorching. To avoid getting dimples in your cured resin, make sure that the temperature in your resin room stays stable, that you use a dustcover and that you only lightly torch your resin!

Leave a Reply

Your email address will not be published. Required fields are marked *