What is needed to make epoxy tumblers?

Along with at least three days, here’s a list of what you’ll need for your first tumbler:

  1. Stainless Steel Tumbler (I used a 20oz)
  2. Spray Paint.
  3. Painters Tape.
  4. Mod Podge.
  5. Silicone Brushes.
  6. Fine Glitter.
  7. Clear Coat Spray.
  8. Epoxy (Both A and B parts)

What can you use instead of epoxy for tumblers?

Are There Any Alternatives to Epoxy if You Want to Make Tumblers?

  • Crystalac (a water-based polyeurethane)
  • Clear Diamond Finish (a clear urethane)
  • 2K Clear Glamour Clear Coat (a spray urethane)

How much epoxy Do I need to mix for a tumbler?

First, you will want to ensure that you allow any spray paint to cure for 36 hours before applying your resin. Second, you will want to add an mL of resin for every ounce of the tumbler (for example, mix 20 ml for a 20 oz tumbler and 30 ml for a 30 oz tumbler and so on) to ensure you have enough resin for your tumbler.

You might be interested:  Question: How To Paint Epoxy?

How long do you turn epoxy tumbler?

Once the entire surface has been evenly covered, allow it to turn until it is dry to the touch, within 18-24 hours. Once dry, remove the tape and allow it to finish curing. At 72 hours, it will have fully cured.

Can you seal a tumbler without epoxy?

Make sure to remove the tape before the Mod Podge dries! There you have it! A way to make a decorated Yeti cup or Ozark tumbler without having to use epoxy. As you can see from the pictures, it’s not as smooth as epoxy but it still works and actually has a nice texture to it!

Can you epoxy plastic tumblers?

Can you do Epoxy on plastic tumblers? Epoxy resin does not adhere to plastic and can peel off in time. If your tumbler has a small amount of plastic on it, you can cover it with a plastic -compatible spray paint to give the resin something to hang onto.

What is the best epoxy for tumblers?

This are the Best Epoxy Resins for Tumblers

  • High Quality Epoxy Resin: Pro Marine ProArt Resin.
  • Review: Art N Glow Casting Resin.
  • Recommendable Epoxy Resin: Envirotex Lite.
  • Metal Tumblers.
  • Plastic Tumblers.
  • Glass & Ceramic Tumblers.
  • Preparation is Key.
  • Mixing and applying the Epoxy to your Tumbler.

What can I use in place of epoxy?

Hard plaster or concrete can be good casting materials, and they’re cheaper than Milliput, Fimo or any resins. Definitely a good low cost material choice for larger pieces.

Can you use Modge podge instead of epoxy?

It works as a sealant to your projects, you can gluwork your project with some classic mod podge and then use the Super Gloss over the top. So it gives you a very shiny, clear finish that looks like epoxy.

You might be interested:  Often asked: How To Make Epoxy Pendants?

Do you have to sand between coats of epoxy on tumbler?

Do you have to sand epoxy tumblers? Sand the entire piece evenly. It will look terrible when you finish sanding it, but don’t worry. After you pour the second coat of epoxy, it will look good as new!

How do you fix tacky epoxy on a tumbler?

How to easily fix sticky Resin

  1. Recoat: Add another fresh layer of doming resin on top of the sticky spots.
  2. Move your artwork into a warmer spot for 24 and let it dry ( resin drying time 20-24 hours ).
  3. Sand the entiry sticky surface off with 80-grit sandpaper and pour another resin coat layer.

Why is my epoxy separating on my tumbler?

Substrate contamination is the most common problem that causes fish eyes and pin holes in epoxy seal coats. Any contamination on the substrate (in the case of surfboards, the fiberglass lamination) will disrupt the surface tension and cause the epoxy to separate or pit. The epoxy will “run away” from contaminated area.

Leave a Reply

Your email address will not be published. Required fields are marked *