- 1 How do you finish an epoxy tumbler?
- 2 What do you clean tumblers with before epoxy?
- 3 Can you seal a tumbler without epoxy?
- 4 How long do you turn epoxy tumbler?
- 5 Should I sand between coats of epoxy?
- 6 Why is my epoxy so bumpy?
- 7 How do you shine epoxy after sanding?
- 8 What is the best epoxy resin for tumblers?
- 9 Is one coat of epoxy enough for a tumbler?
- 10 Do you have to sand between coats of epoxy on tumbler?
- 11 Why is my epoxy cloudy after sanding?
- 12 How long do you wait between epoxy coats?
- 13 How long do you leave cup on Turner after epoxy?
How do you finish an epoxy tumbler?
- Wash tumbler.
- Apply tape to top (and bottom – optional).
- Spray paint the tumbler if needed. Let dry.
- Apply a layer of mod podge with long even strokes.
- Dump glitter all over while you are turning the tumbler so the mod podge is all covered.
- Remove tape.
- Let dry fully (over night).
- Time to epoxy.
What do you clean tumblers with before epoxy?
Sand the tumbler using the wet method, then wash with dawn soap and let air dry. If you try to apply epoxy over stainless steel that has not been sanded/prepped the epoxy will peel off.
Can you seal a tumbler without epoxy?
Make sure to remove the tape before the Mod Podge dries! There you have it! A way to make a decorated Yeti cup or Ozark tumbler without having to use epoxy. As you can see from the pictures, it’s not as smooth as epoxy but it still works and actually has a nice texture to it!
How long do you turn epoxy tumbler?
Once the entire surface has been evenly covered, allow it to turn until it is dry to the touch, within 18-24 hours. Once dry, remove the tape and allow it to finish curing. At 72 hours, it will have fully cured.
Should I sand between coats of epoxy?
You also may need more than one coat if you are putting a clear coat on top of flakes or embedded items. When putting down multiple layers of epoxy for any project, you want to be sure each layer properly bonds with the previous layer. This is why it is best to sand between each layer.
Why is my epoxy so bumpy?
If you have bumpy, spotty, uneven surface, it might be due to not using enough epoxy to coat the object. We did some ornaments and cups and found that if you don’t use enough, no matter how smooth it is at application, it will eventually look like the top picture in this post.
How do you shine epoxy after sanding?
Use a buffing wheel or polishing tool to polish a larger piece of resin. Attach the buffing wheel or polishing tool to a power drill or motor, then move the wheel along the surface of the resin while it’s spinning to polish it.
What is the best epoxy resin for tumblers?
This are the Best Epoxy Resins for Tumblers
- High Quality Epoxy Resin: Pro Marine ProArt Resin.
- Review: Art N Glow Casting Resin.
- Recommendable Epoxy Resin: Envirotex Lite.
- Metal Tumblers.
- Plastic Tumblers.
- Glass & Ceramic Tumblers.
- Preparation is Key.
- Mixing and applying the Epoxy to your Tumbler.
Is one coat of epoxy enough for a tumbler?
Can I put a second coat of epoxy resin? Yes, you can apply a second coat of resin if you need to fix a mistake or a surface imperfection. You can also pour multiple layers if you need to cover areas of high relief, if you’re pouring into a mold or if you simply like the look of a thicker coat..
Do you have to sand between coats of epoxy on tumbler?
Do you have to sand epoxy tumblers? Sand the entire piece evenly. It will look terrible when you finish sanding it, but don’t worry. After you pour the second coat of epoxy, it will look good as new!
Why is my epoxy cloudy after sanding?
Cloudy or dull epoxy is typically caused by excessive moisture. Specifically, moisture from excessive humidity in the area where the epoxy was applied or excessive moisture in/on the concrete application surface. Be sure to eliminate all water before applying epoxy. Never apply epoxy when relative humidity is over 75%
How long do you wait between epoxy coats?
After you pour the second coat of epoxy, it will look good as new! Depending on the epoxy you ‘ve chosen to work with, you ‘ll have to wait between 4 and 24 hours before applying your second coat. Be sure to read your directions very thoroughly before beginning your project.
How long do you leave cup on Turner after epoxy?
Once all epoxy is on the cup keep the cup spinning. Wait about 5-10 minutes and carefully (and with gloves still on) remove the tape from both the top and bottom. If you leave the tape on you ‘ll end up sealing it under the epoxy layer. Let the tumbler turner spin the cup slowly for 6-8 hours.