- 1 Where can I buy Smiths clear penetrating epoxy sealer?
- 2 How do you use clear penetrating epoxy sealer?
- 3 What is clear penetrating epoxy sealer?
- 4 How much penetrating epoxy do I need?
- 5 Can you soak wood in epoxy?
- 6 How do you make penetrating epoxy?
- 7 How do you seal with epoxy?
- 8 What is epoxy wood sealer?
- 9 Is epoxy the same as resin?
- 10 How do you thin penetrating epoxy?
- 11 Does Totalboat epoxy smell?
- 12 Can you use epoxy on hardwood floors?
Where can I buy Smiths clear penetrating epoxy sealer?
CPES ™ ( Clear Penetrating Epoxy Sealer ) and Smith’s Epoxy Fill-it™ are sold on Amazon exclusively by TIMBERCRAFT™.
How do you use clear penetrating epoxy sealer?
Apply by brush, solvent-resistant roller, sprayer, or inject by syringe until wood is completely saturated and will accept no more epoxy. Allow approximately 1–3 days for solvents to evaporate before applying paints, urethanes, varnishes, Fill-It™ Epoxy Filler or regular epoxy resin (see cure time chart below).
What is clear penetrating epoxy sealer?
Clear Penetrating Epoxy Sealer ™ ( CPES ™) consists of a tough, flexible resin system in a solvent blend which dissolves the sap, oil and moisture found in wood. The resin system is derived from natural wood resin and develops a chemical adhesive bond to the wood fibers themselves.
How much penetrating epoxy do I need?
|Size||Penetrating Epoxy Resin (A) Quantity||Total Mixed Quantity|
|Pint Kit||1 Pint||1.5 Pints|
|Quart Kit||1 Quart||1.5 Quarts|
|Half-Gallon Kit||1/2 Gallon||3/4 Gallon|
|Gallon Kit||1 Gallon||1.5 Gallons|
Can you soak wood in epoxy?
Straight epoxy should soak into the wood enough to seal it and keep it from getting wet, but won’t add much if any structural value. Cutting your epoxy with solvents is unlikely to work too well; it may thin the resin, but it’ ll also weaken it, defeating the purpose.
How do you make penetrating epoxy?
Pour parts A & B at a 2:1 mix ratio into mixing cups. Mix parts A & B into one mixing cup and stir for 2-5 minutes. For more penetration into the wood add 50% lacquer thinner or denatured alcohol and mix together. Using a cup or a syringe, pour or inject the epoxy to damaged or rotted area.
How do you seal with epoxy?
- Sand the project.
- Remove all dust from the project with tack cloth.
- Place newspapers or a drop cloth underneath the project.
- Pour epoxy resin and hardener into a clean coffee can.
- Apply epoxy using a bristle brush.
- Check for runs or dry spots as you paint.
- Allow project to cure for 24 hours in a dust-free room.
What is epoxy wood sealer?
TotalBoat Penetrating Epoxy has an easy-to-use, 2-part, low-viscosity formula that penetrates deeply to stop active rot, bonding the surrounding wood to the rotten wood to solidify it. It also seals, preserves, & protects hard and soft woods from mold, mildew, and salt damage.
Is epoxy the same as resin?
The most noticeable difference between these two compounds is their intended use. The Epoxy Coating Resin is intended for coating surface applications, while the Casting Resin is used mainly for jewelry, molds or figurines.
How do you thin penetrating epoxy?
You have two options if you want to thin epoxy using heat. You can heat the resin and hardener components separately and then mix them together to create a thinned epoxy. Or you can heat the substrate – such as wood – and apply your room temperature resin and hardener mix to the heated surface.
Does Totalboat epoxy smell?
Low drip properties ensure smooth and strong coating, laminating, and bonding, and it cures with very low shrinkage. Low VOC content and low odor make it more suitable for shop or garage use where indoor air quality is especially important.
Can you use epoxy on hardwood floors?
Epoxy floor coatings can theoretically be applied to any surface. If you want to refinish a wood floor with epoxy coating, it’s probably not in great condition—so in practice, wood floors should not be epoxy coated. Chemical engineers and flooring experts design epoxy floor coatings to be used primarily with concrete.